FH series motorized ball valve

Features   

• Precisionmetal gear, high strength, reliable performance, long service life

• Multiple wiring for remote control and valve status feedback to intelligent control unit

• Floating sealing ball valve, no leakage

• Low power consumption, battery workable

• Flame retarded PC-ABSenclosure with compact, exquisite structure

• IP 67 protection, applicable for humid environment

• With visual position indicator

• Various connectors customizable

• Manual override for option

Dear Pls contact with me more detail you needs via this email :

liyuchun@flomarvel.com or s.lucky@flomarvel.com

Application

• Automatic remote fluid control for a variety of scenarios, such as smart home, water treatment project, smart water measuring system, firesprinkler system, water supply and drainage system 

Technical parameters

Dimension 

DN       D1/D2      φd     L1    L2/L3   F     H1   H2    W(kg)

DN8     G1/4''      8        45    10       21    68    42    0.26

DN15   G1/2''     15       57    11      25     71    42    0.32

DN20   G3/4''     20       63    12      31     74    42    0.41

DN25   G1''         25       73    16      37     77    42    0.52     unit: mm

Instruction for manual override

1.Manual override function is usually for occasions such as power outage, commissioning etc.
2.Lift the hand-wheel up, observe the open angle through the position indicator, rotate the hand-wheel until the valve is in place.
3.Press down the hand-wheel to switch back to automatic control.

Feature functions for option and purchase guide

Wiring cautions 

※ Make sure that the voltage of power supply meets the requirement of the actuator.  ※ The wiring should comply with local standards and operated by qualified personnel. When installing or repairing, the power should be cut off to prevent electric shock and damage to the equipment.  ※ For the illustration below, the valve is normally closed by default.

OP01 

1. Set SW to [OPEN], the electric valve opens, and it stays in position after it is fully opened.The valve is de-energized (no power consumption).
2. Set SW to [CLOSE], the electric valve closes, and it stays in position after it is fully closed. The valve is de-energized (no power consumption).
※ In case of power loss, valve will remain in its current state.
※ Voltage of power supply for option：5V DC/ 9-35V DC

OP02

1.Both AC and DC power supply workable, while powered with DC power supply,connect the black wire to the (-) pole of power source.
2. Set SW to [OPEN], the electric valve opens, and it stays in position after it is fully opened.The valve is de-energized (no power consumption).
3. Set SW to [CLOSE], the electric valve closes, and it stays in position after it is fully closed. The valve is de-energized (no power consumption).
※ In case of power loss, valve will remain in its current state.
※ Voltages for option：5V DC/ 9-35V DC/220V AC

OP03

1. Both AC and DC power supply workable for OP03. When the power supply is DC, connect red wire to the (+) pole and black wire to the (-) pole .
2. Turn the SW on, the electric valve opens, and it stays in position after it is fully opened.
3. Disconnect the SW, the electric valve closes, and it stays in position after it is fully closed.
※ Voltages for option：5V DC/9-24V ADC/220V AC

OP04

1. Both AC and DC power supply workable. Normal Closed type
Control.
2. Turn the SW on, the electric valve opens, and it stays in position after it is fully opened. There is nominal power consumption.
3. Disconnect the SW (or the power is lost for any other reason ), the electric valve closes.
※ Voltages for option：5V DC/ 9-24V ADC/
110-230V AC

OP05

1.Set SW to [OPEN] - the red wire connect to the (+) pole of power supply, the black wire connect to the (-) pole of power supply, and connect the green wire with fully-open control terminal on the control device, the yellow wire with fully-closed control terminal, white wire is the common wire, when the electric valve fully opens, the green wire outputs valve-fully-open signal, with signal received, the SW is set to switch to STOP position, the valve stops action and keeps in fully open position.
2. Set SW to [CLOSE] - the red wire connect to the (-) pole of power supply, the black wire connect to the (+) pole of power supply, and connect the green wire with fully-open control terminal on the control device, the yellow wire with fully-closed control terminal, white wire is the common wire, when the electric valve fully closes, the yellow wire outputs valve-fully-closed signal, with signal received, the SW is set to switch to STOP position, the valve stops action and keeps in fully closed position.
※ Voltages for option：5V DC/12V DC/24V DC

Feature functions for option

Quick Assemble-and-Disassemble Design for option
※ With adapters mounted to the actuator and valve, the valve and actuator can be assembled and disassembled within 3s, which makes:
①installation and repairing much easier, saves labor cost;
② tremendous reduction in inventory.

Various connectors available for option

※ Various connectors customizable to fit into different control systems and meet requirement of different scenarios.

Welcome to our presentation of the Mini Electric Ball Valve.

This innovative valve is designed and manufactured by our company, the leading source for high-quality valves.

The Mini Electric Ball Valve is a compact and efficient solution for a wide range of industrial applications. Such as: forest fire prevention system.
With its reliable performance and durable construction, it is the perfect choice for engineers and technicians who demand the best.

From HVAC systems to chemical processing plants, this valve is versatile and easy to install. It is also designed for low maintenance, which means less downtime and more productivity.

At our company, we take pride in our commitment to quality and customer satisfaction. We are the source manufacturer of the Mini Electric Ball Valve, which means that we oversee every step of the manufacturing process to ensure that every valve meets our strict standards.

Our state-of-the-art facilities and experienced team of engineers and technicians enable us to produce high-quality valves at a competitive price.

If you have any questions or would like to learn more about the Mini Electric Ball Valve, please contact us at